Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Blog Article
Here in the next paragraph you might get more really good news with regards to Tools You Need to Install a New Bathtub .
Installing a tub isn't exactly rocket science, yet it does require strong plumbing, carpentry, and often, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the task can relocate speedily; if you have to open up a wall surface to remove the old tub and also position the new tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly require a helper to move out the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the job as well as fit trying it. Rather than employing a service provider to take control of a halfway-completed project, it is much better to think about using one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This article will assist you set up a new bathtub in your restroom if you have already gotten a brand-new bathtub and also don't need to change the arrangement of your previous water system pipes.
Your tools and material checklist must make up the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited accessibility that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the staying water that will come from the pipes. Once the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in location in between the faucet and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The former kind should be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using the two wood boards under its feet, place the tub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub up until the level reads level.
To mount taps, fit the bottom of the outermost flexible faucet adapter to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the regular outlet for leaks.
Lastly, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait up until the bath tub has actually been used at least once as this will certainly resolve it right into its last position.
Preparing for the Setup
First of all, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last position.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, causing the water to penetrate the wall surface in between the bath and also the tiling, bring about issues with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very involved in A Step-by-Step Guide to Installing a Bathtub and I am assuming you enjoyed reading the entire blog entry. For those who enjoyed our post if you please do not forget to pass it around. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Book Service Now
Report this page